The kernel data inpage error is a Windows error code presented on a blue screen. When this error happens, your computer will typically compile some diagnostic data and then restart. If the problem persists, your system will eventually crash again with the same kernel data inpage error message.
Kernel data inpage errors are normally associated with hardware failures related to memory modules and hard drives. In other cases, this same error will arise due to the effects of a virus.
How the Kernel Data Inpage Error Appears
When this error happens, you’ll usually see a message like one of these:
Your PC ran into a problem and needed to restart. We’re just gathering some error details, and we’ll restart for you.
If you’d prefer to acknowledge more, you can search online later for this error: KERNEL_DATA_INPAGE_ERROR.
Causes of the Kernel Data Inpage Errors
The kernel data inpage error is a stop code displayed through blue screen crashes and is usually caused by a problem with the random access memory (RAM) or hard drive.
Here are some extra codes associated with this error and the specific problems they refer to:
- 0x0000007A: File access errors
- 0xC000009C: Bad hard drive sectors
- 0xC000009D: Loose cables or hard disk failure
- 0xC000016A: Bad hard drive sectors
- 0xC0000185: Unseated or damaged cables
How to Fix a Kernel Data Inpage Error
Since defective memory modules or hard drives cause most kernel data inpage errors, the fix usually involves locating the malfunctioning component and replacing it.
Computers that undergo this problem usually restart after crashing. If your system won’t turn on or boot up after experiencing a kernel data inpage error.
In other cases, you’ll see that a memory module or hard drive isn’t correctly connected, or a virus caused the entire problem. Follow these troubleshooting moves to fix your Kernal data inpage error:
Back up your data. If it’s a difficulty with your hard drive, you could end up losing important data. If you have anything stored on your system you don’t want to lose, you should perform a backup before starting the diagnostic process. Make copies of any files you can’t afford to lose, and save them on a USB drive, SD card, or cloud storage service.
Inspect and reseat your memory modules
In some circumstances, the problem can be made by improperly seated memory modules. To rule this out and prevent any needless expenses, open your computer and inspect you’re RAM. If any modules aren’t perfectly installed or have come loose, reseat them and check to see if the kernel data inpage error still occurs.
Exercise caution when opening a system and adjusting components. Without an accurately set up anti-static bracelet, static electricity may permanently damage components like RAM.
Inspect and reseat your hard drive cables
This error usually shows that the drive has physical defects like bad sectors. In some cases, you may experience this problem due to an inadequately seated hard drive cable.
To rule this possibility out, open your system, locate your hard drive, and reseat the connector cable. You’ll also require to check and reseat the cable where it connects to your motherboard.
When your hard drive is running, listen carefully to any loud clicking noises. If you hear them, your hard drive may be in the method of failing, which can cause this type of error. The fix is to back up all of your data and reinstate your hard drive.
Test your memory
Windows 10 has a built-in memory diagnostic tool. There are also amazing free options available for Windows 7, Windows 8, and Windows 10. If you have Windows 10, type “memory” into the taskbar search field, select Windows Memory Diagnostic > Restart now, and check for problems.
The best free memory diagnostic tool is MemTest 86, which you can download and utilize to check your RAM.
You may need to run more than one memory diagnostic tool. If any of these tools report difficulty with your memory, consider replacing your RAM. Doing so will apparently fix your kernel data inpage error, but your RAM is likely to fail in the future either way if one of these tools finds a problem.
Test your hard drive
You can check for your hard drive problems using the built-in Windows error-checking tool or the chkdsk command.
If your diagnostic tool of selection finds any problems, like bad sectors, allow it to attempt a fix. If successful, you should use your system without any further kernel data inpage error crashes.
Unplug hardware peripherals
While less likely, this error can happen due to other peripherals. To rule this out, shut down your system, unplug all of your hardware peripherals, and turn your computer back on.
If your system doesn’t crash with the kernel data inpage error, reconnect each device one at a time. When you find the device causing the issue, you can either leave it unplugged or replace it.
Run a virus scan
In some cases, a virus may corrupt essential files and cause a kernel data inpage error. This is less likely than other chances, but it’s still important to check.
If nothing else has worked, decide to run a virus scan. If any of these programs locate a virus, allow it to fix the problem, check to see if you are still experiencing kernel data inpage errors.
[wps_faq style=”classic” question=”Q: What is kernel data?”]A: KERNEL DATA INPAGE ERROR is a standard Blue Screen of Death (BSOD) error code—also known as stop code—which appears when a system suffers from a severe hardware or software problem that it couldn’t handle.[/wps_faq][wps_faq style=”classic” question=”Q: What causes kernel security check failure?”]A: The installed software conflicts can cause the Kernel Security Check Failure. In addition to that, if your computer has memory problems, virus infection, driver incompatibility or outdated issues, corrupted Windows system files, and hard disk errors, you can get the stop code Kernel Security Check Failure.[/wps_faq][wps_faq style=”classic” question=”Q: Is the blue screen of death fixable?”]A: The Blue Screen of Death is real—but fixable.[/wps_faq]